noobbritish.blogg.se - Phoenix awardbios cmos setup utility factory reset

#PHOENIX AWARDBIOS CMOS SETUP UTILITY FACTORY RESET PASSWORD#
#PHOENIX AWARDBIOS CMOS SETUP UTILITY FACTORY RESET WINDOWS#

See the " Removing a BIOS password" page of their online support.

#PHOENIX AWARDBIOS CMOS SETUP UTILITY FACTORY RESET PASSWORD#

You need to send your laptop for repair to allow Packard Bell to remove the password of your BIOS. If you have a Packard Bell laptop, know that there is an official (but paid) solution. The BIOS will tell you which settings will be restored to their original values.Ĭlick OK and the computer will restart normally.Ĥ. Then, click "Save Changes & Reset" to save the changes. If you are in the advanced mode, go to the "Exit" tab and click "Load Optimized Defaults". Then, if you are in the EZ Mode, you will find the "Default" option at the bottom of the screen.

If you have an Asus motherboard with this type of BIOS, press DEL or F2 when you start your computer to enter in the BIOS. Then, click on the "Exit/Advanced Mode" button at the top right. If you have an Asus motherboard with a BIOS that looks like this, you will find a "Default (F5)" button at the bottom right of the screen.Ī small window will appear with the "Load Optimized Defaults?" message.

Then, type Y, and then press Enter to save the changes. If the computer does not restart, press F10 (Save & Exit Setup). Then, select the "Load Optimized Defaults" option and press Enter. If you have an Award BIOS, press the DEL key of your keyboard when you start your computer. Then, go to the Exit tab and choose the "Load Setup Defaults" option.įinally, select "Exit Saving Changes" and press Enter. If you have a PhoenixBIOS, enter in the BIOS by pressing F2 when you start your computer. Typically, this option is in the "Exit" (or Quit) tab of your BIOS. Use the Load Defaults feature of the BIOSĪnd finally, the 3rd solution to reset the BIOS is to use the "Load Setup Defaults", "Load Fail-Safe Defaults" or "Load Optimized Defaults" option present in all BIOS. Then, your computer will restart correctly. In this case, buy a new CR2032 battery (3 volts). Note : if this message appears every time you start up, the battery is discharged. then quit the BIOS by saving the changes (even if you have not done a changes). return at least once in the BIOS (by using the key indicated or the usual key (DEL, F2. Note that a "CMOS Checksum Bad" message may appear once at startup. puis, quitter le BIOS en sauvegardant les changements (même si vous n'en avez pas fait). rentrer au moins une fois dans le BIOS (via la touche indiquée ou la touche habituelle (DEL, SUPPR, F2. Notez qu'il est possible qu'un message "CMOS Checksum Bad" s'affiche une fois au démarrage. Then, clip it back on the motherboard (in the correct position) and start your computer.

Then, remove the battery of the motherboard for at least 30 seconds.

Unplug the power plug from your computer.

The easiest and least risky solution is to : Temporarily removing the battery from the motherboard (desktop PC)

If you had changed a setting necessary for the proper functioning of your system.

In this case, follow this : Create and configure a RAID 0, 1, 5.

If you had enabled the RAID technology of your motherboard.

If you are using virtualization technologies such as VirtualBox or VMware, you will need to enable the processor virtualization : Enable virtualization (Intel VT-x / AMD-V).

#PHOENIX AWARDBIOS CMOS SETUP UTILITY FACTORY RESET WINDOWS#

Otherwise, a STOP blue screen will be displayed each time Windows starts.

If you changed the hard disk controller before resetting the BIOS, you will need to restore the correct value by following these steps : Change the mode of the hard disk controller.

No, because this will not make your computer permanently unusable.Īnd not if you have never changed an advanced setting in your BIOS.

Use a third-party program (risky, so to use as a last resort).

Use the Load Defaults feature of the BIOS.

Temporarily removing the battery from the motherboard (desktop PC).

When you enter the BIOS of your motherboard, you can modify many things (see the " BIOS" category of our site for interesting options).īut if you no longer know what you have changed or if you lose the BIOS password you have set up a long time ago, the simplest solution is to reset the BIOS of your computer.įor that, there are several possibilities, but the last solution must be used only as a last resort.